CNC Machines for Steel Structure
©À Aerial Insulation Conductor Fitting
©À T-connector
©À Link Fitting
TPHD1616 /TPHD2016 High Speed CNC Drilling Machine
2016-6-16 16:23:58
Applicable Industry: The machine is mainly used in steel structure drilling in construction, bridge, tower etc., and can be use din pipe and plate of boiler, petro line, baffle plate and round flange. And the machine can be used drilling through-hole, blind hole, ladder hole, chamfer for hole-end.
Product composition:
Ø Worktable with 12 sets hydraulic clamps
Ø Thickened and enhanced movable gantry
Ø High speed drill head
Ø Electric cabinet with CNC system
Ø Hydraulic Station
Ø Automatic chip conveyor with chip carriage
Ø Automatic recycling cooling water system
Main Description:
Ø Function: Drilling, Tapping, Milling, Chamfering and so so.
Ø Work-piece: Steel Plates, Flanges, Tube Sheets, Pressure Vessels and so on.
Ø High precision£º¡À0.08mm
Ø High rotation speed£º30~3000 r/min
Ø Twelve floating hydraulic clamps, four sets work-pieces can be clamped simultaneously.
Technical Parameters£º
Model |
TPHD1616 |
TPHD2012 |
Max work piece size (L¡ÁW) |
1600X1600mm plate or ¦µ1600mm flange |
2000X1200mm plate or ¦µ1200mm flange |
Thickness of work piece |
6--120mm |
6--120mm |
Drill unit type |
sliding table, servo control |
sliding table, servo control |
Drill head quantity |
Ò»¸öone |
Ò»¸öone |
Max drill diameter |
¦µ40mm |
¦µ40mm |
Taper hole of spindle |
BT40 |
BT40 |
Spindle speed |
30¡«3000r/min (frequency control) |
30¡«3000r/min (frequency control) |
Spindle vertical stoke (Z axis) |
150mm |
150mm |
Servo motor power of X axis |
2.0 kW |
2.0 kW |
Servo motor power of Y axis |
1. 5 kW |
1. 5 kW |
Servo motor power of Z axis |
2.0 kW |
2.0 kW |
Motor power of chip cleaner |
0.4 kW |
0.4 kW |
Motor power of cooling system |
0.43+2.2+7.5 kW |
0.43+2.2+7.5 kW |
Clamping type |
12 Hydraulic clams and T-slot |
12 Hydraulic clams and T-slot |
Electric control type |
808D SIMENS 808D |
808D SIMENS 808D |
CNC axis quantity |
3 |
3 |
Position precision |
¡À0.08mm |
¡À0.08mm |
With function of CAD/CAM automatic generation | ||
With function of hole site memory (memory hole site if power off suddenly) and drill pause | ||
Overall size |
About 4.5X3.9X3m |
About 5.3x3.9x3m |
Weight |
About 12t |
About 14.5t |
Product Feature:
1. CNC slide way drilling spindle (Z axis) with work piece of stroke is pre-set, realized auto switch. It can drill not only through-hole, but also blind-hole with characteristic of high efficiency, simple-structure, low-cost maintenance, easy operation etc.
2. This machine the work piece is tight by hydraulic clamp cards, the operation of the workers with foot switch control, easy to operate, and effort; the largest single piece of up to 2000¡Á1200mm, small work pieces can be clamped to the four corners of the table, and can significantly shorten the production preparation period, improve production efficiency.
3. This machine is a total of three CNC axes: gantry mobile (x-axis);drilling power head in the mobile gantry beam (y-axis); of the advance and retreat movement of the spindle (z axis). Each CNC axes using precision linear rolling guide oriented AC servo motor and ball screw drive. The movement is flexible, accurate positioning.
4. This machine is more than a splint group, clamping it was easier to design are taken into consideration when processing circular plate of the boiler industry, hole-intensive, so the work on stage scale steel ruler and as mall support block, according to the work piece position of the hole size mobile support blocks, to escape the position of the hole.
5. CNC adopt SIMENS 808D control, equipped with a host computer to facilitate the storage and input of the work piece program, easy to operate.
6. The configuration of the machine tool ball screws, linear guides, electrical, servo motor, inverter, etc., are well-known foreign manufacturers supply. Failure Boot rate.